Here is a list of all available COP Commands
1/2021-ve3wzw
* cop (control operator) cmds: *
* 1 - System warm boot
* 2 - System enable
* 3 - System disable
* 4 - Test Tone On/Off
* 5 - Dump System Variables on Console (debug)
* 6 - PTT (phone mode only)
* 7 - Time out timer enable
* 8 - Time out timer disable
* 9 - Autopatch enable
* 10 - Autopatch disable
* 11 - Link enable
* 12 - Link disable
* 13 - Query System State
* 14 - Change System State
* 15 - Scheduler Enable
* 16 - Scheduler Disable
* 17 - User functions (time, id, etc) enable
* 18 - User functions (time, id, etc) disable
* 19 - Select alternate hang timer
* 20 - Select standard hang timer
* 21 - Enable Parrot Mode EXAMPLE 971=cop,21; enable Parrot Mode *971 to execute * 22 - Disable Parrot Mode
* 23 - Birdbath (Current Parrot Cleanup/Flush)
* 24 - Flush all telemetry
* 25 - Query last node un-keyed
* 26 - Query all nodes keyed/unkeyed
* 27 - Reset DAQ minimum on a pin
* 28 - Reset DAQ maximum on a pin
* 30 - Recall Memory Setting in Attached Xcvr
* 31 - Channel Selector for Parallel Programmed Xcvr
* 32 - Touchtone pad test: command + Digit string + # to playback all digits pressed
* 33 - Local Telemetry Output Enable
* 34 - Local Telemetry Output Disable
* 35 - Local Telemetry Output on Demand
* 36 - Foreign Link Local Output Path Enable
* 37 - Foreign Link Local Output Path Disable
* 38 - Foreign Link Local Output Path Follows Local Telemetry
* 39 - Foreign Link Local Output Path on Demand
* 42 - Echolink announce node # only
* 43 - Echolink announce node Callsign only
* 44 - Echolink announce node # & Callsign
* 45 - Link Activity timer enable
* 46 - Link Activity timer disable
* 47 - Reset "Link Config Changed" Flag
* 48 - Send Page Tone (Tone specs separated by parenthesis)
* 49 - Disable incoming connections (control state noice)
* 50 - Enable incoming connections (control state noicd)
* 51 - Enable sleep mode
* 52 - Disable sleep mode
* 53 - Wake up from sleep
* 54 - Go to sleep
* 55 - Parrot Once if parrot mode is disabled
* 56 - Rx CTCSS Enable
* 57 - Rx CTCSS Disable
* 58 - Tx CTCSS On Input only Enable
* 59 - Tx CTCSS On Input only Disable
* 60 - Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode])
* Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call
* (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F.
* DestID and subcode are only specified for the 'C' type message.
* UnitID is the local systems UnitID. DestID is the MDC1200 ID of
* the radio being called, and the subcodes are as follows:
* Subcode '8205' is Voice Selective Call for Spectra ('Call')
* Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or
* Astro-Saber('Call')
* Subcode '810D' is Call Alert (like Maxtrac 'CA')
* 61 - Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....)
* 62 - Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....) * 63 - Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR])
* 64 - Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR])
* 65 - Send POCSAG page (equipped channel types only)
1/2021-ve3wzw
No comments:
Post a Comment
.
Allstar // AllstarLink -
https://groups.io/g/Allstar
.