Allstar Internal Commands

 Allstar Internal Commands

 The following commands are defined internally in Allstar and can be

executed in the Asterisk client or mapped to DTMF functions as

needed.

Status Commands:

  1 - Force ID (global)

  2 - Give Time of Day (global)

  3 - Give software Version (global)

  4 - Give GPS location info

  5 - Last (dtmf) user

 11 - Force ID (local only)

 12 - Give Time of Day (local only)

COP (control operator) Commands:

 1 - System warm boot

 2 - System enable

 3 - System disable

 4 - Test Tone On/Off

 5 - Dump System Variables on Console (debug)

 6 - PTT (phone mode only)

 7 - Time out timer enable

 8 - Time out timer disable

 9 - Autopatch enable

 10 - Autopatch disable

 11 - Link enable

 12 - Link disable

 13 - Query System State

 14 - Change System State

 15 - Scheduler Enable

 16 - Scheduler Disable

 17 - User functions (time, id, etc) enable

 18 - User functions (time, id, etc) disable

 19 - Select alternate hang timer

 20 - Select standard hang timer

 21 - Enable Parrot Mode

 22 - Disable Parrot Mode

 23 - Birdbath (Current Parrot Cleanup/Flush)

 24 - Flush all telemetry

 25 - Query last node un-keyed

 26 - Query all nodes keyed/unkeyed

 27 - Reset DAQ minimum on a pin

 28 - Reset DAQ maximum on a pin

 30 - Recall Memory Setting in Attached Xcvr

 31 - Channel Selector for Parallel Programmed Xcvr

 32 - Touchtone pad test: command + Digit string + # to playback all

      digits pressed

 33 - Local Telemetry Output Enable

 34 - Local Telemetry Output Disable

 35 - Local Telemetry Output on Demand

 36 - Foreign Link Local Output Path Enable

 37 - Foreign Link Local Output Path Disable

 38 - Foreign Link Local Output Path Follows Local Telemetry

 39 - Foreign Link Local Output Path on Demand

 42 - Echolink announce node # only

 43 - Echolink announce node Callsign only

 44 - Echolink announce node # & Callsign

 45 - Link Activity timer enable

 46 - Link Activity timer disable

 47 - Reset "Link Config Changed" Flag

 48 - Send Page Tone (Tone specs separated by parenthesis)

 49 - Disable incoming connections (control state noice)

 50 - Enable incoming connections (control state noicd)

 51 - Enable sleep mode

 52 - Disable sleep mode

 53 - Wake up from sleep

 54 - Go to sleep

 55 - Parrot Once if parrot mode is disabled

 56 - Rx CTCSS Enable

 57 - Rx CTCSS Disable

 58 - Tx CTCSS On Input only Enable

 59 - Tx CTCSS On Input only Disable

 60 - Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode])

      Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call

      (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F.

      DestID and subcode are only specified for  the 'C' type

      message.

      UnitID is the local systems UnitID. DestID is the MDC1200 ID

      of the radio being called, and the subcodes are as follows:

      Subcode '8205' is Voice Selective Call for Spectra ('Call')

      Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or

      Astro-Saber('Call')

      Subcode '810D' is Call Alert (like Maxtrac 'CA')

 61 - Send Message to USB to control GPIO pins

      (cop,61,GPIO1=0[,GPIO4=1].....)

 62  - Send Message to USB to control GPIO pins, quietly

      (cop,62,GPIO1=0[,GPIO4=1].....)

 63 - Send pre-configred APRSTT notification

      (cop,63,CALL[,OVERLAYCHR])

 64 - Send pre-configred APRSTT notification, quietly

     (cop,64,CALL[,OVERLAYCHR])

 65 - Send POCSAG page (equipped channel types only)